fr 2 al thru fr 2 ml 2 amp fast recovery silicon rectifier 50 to 1000 volts features easy pick and place high temp soldering: 260 c for 10 seconds at terminals superfast recovery times for high efficiency maximum ratings operating temperature: -50 c to +150 c storage temperature: -50 c to +150 c maximum thermal resistance; 15 c/w junction to lead mcc catalog number device marking maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage fr2al fr2a 50v 35v 50v fr2bl fr2b 100v 70v 100v fr2dl fr2d 200v 140v 200v fr2gl fr2g 400v 280v 400v FR2JL fr2j 600v 420v 600v fr2kl fr2k 800v 560v 800v fr2ml fr2m 1000v 700v 1000v electrical characteristics @ 25 c unless otherwise specified average forward current i f(av) 2.0a t a = 90 c peak forward surge current i fsm 50a 8.3ms, half sine maximum instantaneous forward voltage v f 1.30v i fm = 2.0a; t j = 25 c* maximum dc reverse current at rated dc blocking voltage i r 5 m a 200 m a t j = 25 c t j = 125 c maximum reverse recovery time fr2al-gl FR2JL fr2kl-ml t rr 150ns 250ns 500ns i f =0.5a, i r =1.0a, i rr =0.25a typical junction capacitance c j 40pf measured at 1.0mhz, v r =4.0v *pulse test: pulse width 300 m sec, duty cycle 1% do-214aa (smb) (lead frame) 0.070? 0.090" 0. 0 85 ? suggested solder pad layout h j e f g a b d c
omp onents 2 0736 marilla street chatsworth ! " # $
% ! " # mcc revision: 5 2006/05/19 a b d c dimensions inches mm dim min max min max note a .075 .095 1.91 2. 41 b .077 .0 8 3 1.96 2. 10 c .002 .008 .05 .20 d ---- - .02 ----- .51 e .0 3 0 .060 .76 1.52 g .2 0 0 .2 2 0 5.08 5.59 h .160 .187 4.06 4.75 j .130 .155 3.30 3.94 tm micro commercial components ? case material: molded plastic. ul flammability classification rating 94v-0 www. mccsemi .com 1 of 4
fr2al thru fr2ml average forward rectified current - amperes versus ambient temperature - c figure 2 forward derating curve 0 17550 75 100 125 0 .5 1.0 1.5 single phase, half wave 60hz resistive or inductive load amps c 150 2.0 2.5 3.0 junction capacitance - pf versus reverse voltage - volts instantaneous forward current - amperes versus instantaneous forward voltage - volts figure 1 typical forward characteristics 4 6 20 10 amps .4 .6 .8 1.0 1.2 1.4 .01 .02 .04 .06 .1 .2 .4 .6 1 2 25 c volts figure 3 junction capacitance .1 .2 1 .4 2 10 20 404 100 200 1 2 6 10 20 100 pf volts 60 40 4 400 1000 t j =25 c mcc revision: 5 2006/05/19 tm micro commercial components www. mccsemi .com 2 of 4
fr2al thru fr2ml t rr +0.5a 0 -0.25 -1.0 1cm set time base for 20/100ns/cm 25vdc 1 w 50 w 10 w oscilloscope note 1 pulse generator note 2 notes: 1. rise time = 7ns max. input impedance = 1 megohm, 22pf 2. rise time = 10ns max. source impedance = 50 ohms 3. resistors are non-inductive figure 5 reverse recovery time characteristic and test circuit diagram 1 100 4 0 15 30 45 8 figure 4 maximum non-repetitive forward surge current peak forward surge current - amperes versus number of cycles at 60hz - cycles amps cycles 2 6 10 20 60 80 40 60 75 90 mcc revision: 5 2006/05/19 tm micro commercial components www. mccsemi .com 3 of 4
mcc www.mccsemi .com revision: 5 2006/05/19 tm micro commercial components www. mccsemi .com 4 of 4 products are represented on our website, harmless against all damages. ***applications disclaimer*** ***important notice*** aerospace or military applications. products offer by micro commercial components corp . are not intended for use in medical, micro commercial components corp . reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . micro commercial components corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . the user of products in such applications shall assume all risks of such use and will agree to hold micro commercial components corp . and all the companies whose
|
